WebOS Signage/en: различия между версиями

Материал из SmartPlayer
(Новая страница: «<h3> [Alternative] Manual installation of the application: </h3> # On the remote control Quickly enter the combination of buttons 8080 + "OK" button. '' 'On WebOS...»)
Нет описания правки
 
(не показано 8 промежуточных версий 2 участников)
Строка 38: Строка 38:
# Reload prof. panel.
# Reload prof. panel.


<h3>2. Массовая установка приложения с помощью ПО Beanstaller</h3>
<h3> 2nd method Bulk application installation using Beanstaller </h3>
При подключении устройств и компьютера администратора в общую сеть оптимальным вариантом будет использовать ПО Beanstaller.  
When connecting devices and the administrator's computer to a shared network, the best option is to use the Beanstaller software.
Beanstaller обычно используется при массовой установки (более 20 устройств за раз) приложения. Beanstaller - позволит максимально оперативно прописать настройки для установки приложения с компьютера администратора. ПО Beanstaller можно запросить у представителя SmartPlayer.  
Beanstaller is commonly used when bulking installations (more than 20 devices at a time) of an application. Beanstaller - will allow you to quickly register the settings for installing the application from the administrator's computer. Beanstaller software can be requested from a SmartPlayer representative.  


<h3>3. USB установка приложения с помощью USB stick и файла scap_installation.json</h3>
<h3> 3. USB installation of the application using a USB stick and scap_installation.json file </h3>
Данная установка используется при установки приложения по USB FLASH.
'''3.1 Preparing flash storage (USB flash drive)'''
#Запишите в корень флешки файл scap_installation.json полученный от представителя SmartPlayer.
# Format the flash drive to NTFS format
#Вставьте флешку в проф. панель.
# Put the file [http://sa2.org/w/scap_installation.json scap_installation.json] in the root of the flash drive
#Перезагрузите устройство.
'''3.2 Preparing the device'''
Приложение будет скачано, установлено и запущено после перезагрузки.
# If the device has been used before, make it a factory reset. If the device has not been used before, skip this step.
# Connect the device to the network via RJ45 with Internet access, in other words, insert the Internet cable into the device connector.
# Insert the USB flash drive into the USB connector of the device, prepared in paragraph 3.1
# Turn on the device from the control panel by pressing the tap button or on in the monitor section
'''3.3 Installing the application'''
# Do nothing, the device will reboot once and show the registration code in the SmartPlayer platform. Submit to https://cms.smartplayer.org/ and register your device for further work.
# Remove the USB flash drive from the device's USB connector


== Сброс панели до заводских настроек ==
== Reset the panel to factory settings ==
*На пульте нажимаем SETTINGS.
* On the remote control press SETTINGS.
*В открывшемся меню выбираем вкладку Admin
* In the menu that opens, select the Admin tab
*Переводим переключатель из положения OFF, в положение ON. Система попросит ввести пароль, по умолчанию 0000.
* Turn the switch from the OFF position to the ON position. The system will ask you to enter a password, the default is 0000.
*Выбираем пункт factory reset - confirm
* Select factory reset - confirm


Если в процессе скачивания и установки возникла проблема обратитесь к соответствующему разделу, с возможными проблемами и способами их решения [[Troubleshooting|ЗДЕСЬ]].
If a problem occurs during the download and installation process, refer to the appropriate section, with possible problems and solutions [[Troubleshooting | HERE]].


== Обновление прошивки (актуально для WebOS 3, WebOS 3.2, WebOS 4) ==  
== Firmware update (relevant for WebOS 3, WebOS 3.2, WebOS 4) ==  


*Скачать официальную прошивку на сайте LG или по ссылке предоставляемой представителями SmartPlayer
* Download the official firmware on the LG website or via the link provided by SmartPlayer representatives
*Создать на usb флешке папку с именем LG_MONITOR и перенести прошивку в данную папку
* Create a folder on the usb flash drive with the name LG_MONITOR and transfer the firmware to this folder
*Вставить флешку в панель, зайти в меню пункт General, далее нажимаем сем раз нажимаем цифру 7 на пульте.  
* Insert a USB flash drive into the panel, go to the menu item General, then press this button seven times, press number 7 on the remote control.
*Переходим в меню обновления прошивки, выбираем файл обновления который будем устанавливать
* Go to the firmware update menu, select the update file that we will install
*Нажимаем UPDATE
* Press UPDATE
'''Важно!!!'''  
'''Important!!!'''
*Если вы хотите обновить прошивку на более раннюю версию то перед обновление нужно выключить в меню переключатель Ext. MICOM
* If you want to upgrade the firmware to an earlier version, before upgrading you need to turn off the Ext switch in the menu. MICOM

Текущая версия от 12:50, 17 сентября 2021

Другие языки:

Description

WebOS LG professional panels with an integrated player (System on Chip).

Initial setup

In the case of the first start-up of the device (the device has not been used anywhere before), a setup wizard should appear (a greeting with a question about choosing a language, country, and time zone).

First time you turn on the device (new device)

When you turn on the device for the first time, you need to configure basic parameters such as language, operating mode, and playback method using the setup wizard.
'For panels based on WebOS 2.0, it is also necessary to turn off the shutdown after 4 hours of operation:'

  1. Hold the "settings" button until a notification appears in the upper right corner of the screen
  2. Dial 0000 and press the "OK" button.
  3. In the window that appears, select "Signage Setup".
  4. Select "Auto Power Off" and indicate "OFF".

Before start

'Before starting the SmartPlayer app, make sure that you are using the latest / recommended version of the firmware.'

'WebOS 2.0 / WebOS 3.0'
On the remote control, press the "Home" button, select System Information / Information.
'WebOS 3.2 / WebOS 4.0'
On the remote control, press the "Home" button, select the tile S / W Version

Be sure to set the correct time or use the NTP Server.

NTP Configuration:

  1. Press Settings button on remote
  2. General -> Time & Date
  3. Select Set Automatically

[Alternative] Manual installation of the application:

  1. On the remote control Quickly enter the combination of buttons 8080 + "OK" button. 'On WebOS2.0 and 3.0' hold the "settings" button until a notification appears in the upper right corner of the screen 8080 + "OK" button
  2. Select EZ SETTINGS -> SI Server Settings.
  3. Select SI Server Settings.
  4. Fill in the parameters as shown in the image, replacing the application address with the representative of SmartPlayer provided to you. 'Important!!! AutoSet must be set to off. If this is not done, the application will not be able to update from the SmartPlayer server. Actual forwebOS4 and higher. '
  5. Select Local Application Upgrade: Remote.
  6. Wait for application update
  7. Reload prof. panel.

2nd method Bulk application installation using Beanstaller

When connecting devices and the administrator's computer to a shared network, the best option is to use the Beanstaller software. Beanstaller is commonly used when bulking installations (more than 20 devices at a time) of an application. Beanstaller - will allow you to quickly register the settings for installing the application from the administrator's computer. Beanstaller software can be requested from a SmartPlayer representative.

3. USB installation of the application using a USB stick and scap_installation.json file

3.1 Preparing flash storage (USB flash drive)

  1. Format the flash drive to NTFS format
  2. Put the file scap_installation.json in the root of the flash drive

3.2 Preparing the device

  1. If the device has been used before, make it a factory reset. If the device has not been used before, skip this step.
  2. Connect the device to the network via RJ45 with Internet access, in other words, insert the Internet cable into the device connector.
  3. Insert the USB flash drive into the USB connector of the device, prepared in paragraph 3.1
  4. Turn on the device from the control panel by pressing the tap button or on in the monitor section

3.3 Installing the application

  1. Do nothing, the device will reboot once and show the registration code in the SmartPlayer platform. Submit to https://cms.smartplayer.org/ and register your device for further work.
  2. Remove the USB flash drive from the device's USB connector

Reset the panel to factory settings

  • On the remote control press SETTINGS.
  • In the menu that opens, select the Admin tab
  • Turn the switch from the OFF position to the ON position. The system will ask you to enter a password, the default is 0000.
  • Select factory reset - confirm

If a problem occurs during the download and installation process, refer to the appropriate section, with possible problems and solutions HERE.

Firmware update (relevant for WebOS 3, WebOS 3.2, WebOS 4)

  • Download the official firmware on the LG website or via the link provided by SmartPlayer representatives
  • Create a folder on the usb flash drive with the name LG_MONITOR and transfer the firmware to this folder
  • Insert a USB flash drive into the panel, go to the menu item General, then press this button seven times, press number 7 on the remote control.
  • Go to the firmware update menu, select the update file that we will install
  • Press UPDATE

Important!!!

  • If you want to upgrade the firmware to an earlier version, before upgrading you need to turn off the Ext switch in the menu. MICOM